RFC1155-SMI DEFINITIONS ::= BEGIN nullOID OBJECT IDENTIFIER ::= { ccitt 0 } internet OBJECT IDENTIFIER ::= { iso org(3) dod(6) 1 } directory OBJECT IDENTIFIER ::= { internet 1 } mgmt OBJECT IDENTIFIER ::= { internet 2 } experimental OBJECT IDENTIFIER ::= { internet 3 } private OBJECT IDENTIFIER ::= { internet 4 } enterprises OBJECT IDENTIFIER ::= { private 1 } END -- @(#)WSCCS o/mibs-rfc1213.mib 1.1 8/30/95 -- Changes to rfc1213 (MIB-II): -- No changes needed. RFC1213-MIB DEFINITIONS ::= BEGIN IMPORTS mgmt, NetworkAddress, IpAddress, Counter, Gauge, TimeTicks FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; -- This MIB module uses the extended OBJECT-TYPE macro as -- defined in [14]; -- MIB-II (same prefix as MIB-I) mib-2 OBJECT IDENTIFIER ::= { mgmt 1 } -- textual conventions DisplayString ::= OCTET STRING -- This data type is used to model textual information taken -- from the NVT ASCII character set. By convention, objects -- with this syntax are declared as having -- -- SIZE (0..255) PhysAddress ::= OCTET STRING -- This data type is used to model media addresses. For many -- types of media, this will be in a binary representation. -- For example, an ethernet address would be represented as -- a string of 6 octets. -- groups in MIB-II system OBJECT IDENTIFIER ::= { mib-2 1 } interfaces OBJECT IDENTIFIER ::= { mib-2 2 } at OBJECT IDENTIFIER ::= { mib-2 3 } ip OBJECT IDENTIFIER ::= { mib-2 4 } icmp OBJECT IDENTIFIER ::= { mib-2 5 } tcp OBJECT IDENTIFIER ::= { mib-2 6 } udp OBJECT IDENTIFIER ::= { mib-2 7 } egp OBJECT IDENTIFIER ::= { mib-2 8 } -- historical (some say hysterical) -- cmot OBJECT IDENTIFIER ::= { mib-2 9 } transmission OBJECT IDENTIFIER ::= { mib-2 10 } snmp OBJECT IDENTIFIER ::= { mib-2 11 } -- the System group -- Implementation of the System group is mandatory for all -- systems. If an agent is not configured to have a value -- for any of these variables, a string of length 0 is -- returned. sysDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters." ::= { system 1 } sysObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'." ::= { system 2 } sysUpTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The time (in hundredths of a second) since the network management portion of the system was last re-initialized." ::= { system 3 } sysContact OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "The textual identification of the contact person for this managed node, together with information on how to contact this person." ::= { system 4 } sysName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name." ::= { system 5 } sysLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "The physical location of this node (e.g., `telephone closet, 3rd floor')." ::= { system 6 } sysServices OBJECT-TYPE SYNTAX INTEGER (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted." ::= { system 7 } -- the Interfaces group -- Implementation of the Interfaces group is mandatory for -- all systems. ifNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of network interfaces (regardless of their current state) present on this system." ::= { interfaces 1 } -- the Interfaces table -- The Interfaces table contains information on the entity's -- interfaces. Each interface is thought of as being -- attached to a `subnetwork'. Note that this term should -- not be confused with `subnet' which refers to an -- addressing partitioning scheme used in the Internet suite -- of protocols. ifTable OBJECT-TYPE SYNTAX SEQUENCE OF IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A list of interface entries. The number of entries is given by the value of ifNumber." ::= { interfaces 2 } ifEntry OBJECT-TYPE SYNTAX IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An interface entry containing objects at the subnetwork layer and below for a particular interface." INDEX { ifIndex } ::= { ifTable 1 } IfEntry ::= SEQUENCE { ifIndex INTEGER, ifDescr DisplayString, ifType INTEGER, ifMtu INTEGER, ifSpeed Gauge, ifPhysAddress PhysAddress, ifAdminStatus INTEGER, ifOperStatus INTEGER, ifLastChange TimeTicks, ifInOctets Counter, ifInUcastPkts Counter, ifInNUcastPkts Counter, ifInDiscards Counter, ifInErrors Counter, ifInUnknownProtos Counter, ifOutOctets Counter, ifOutUcastPkts Counter, ifOutNUcastPkts Counter, ifOutDiscards Counter, ifOutErrors Counter, ifOutQLen Gauge, ifSpecific OBJECT IDENTIFIER } ifIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization." ::= { ifEntry 1 } ifDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface." ::= { ifEntry 2 } ifType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10Mbit(12), proteon-80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), ds1(18), -- T-1 e1(19), -- european equiv. of T-1 basicISDN(20), primaryISDN(21), -- proprietary serial propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), -- CLNP over IP [11] ethernet-3Mbit(26), nsip(27), -- XNS over IP slip(28), -- generic SLIP ultra(29), -- ULTRA technologies ds3(30), -- T-3 sip(31), -- SMDS frame-relay(32) } ACCESS read-only STATUS mandatory DESCRIPTION "The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack." ::= { ifEntry 3 } ifMtu OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface." ::= { ifEntry 4 } ifSpeed OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth." ::= { ifEntry 5 } ifPhysAddress OBJECT-TYPE SYNTAX PhysAddress ACCESS read-only STATUS mandatory DESCRIPTION "The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { ifEntry 6 } ifAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } ACCESS read-write STATUS mandatory DESCRIPTION "The desired state of the interface. The testing(3) state indicates that no operational packets can be passed." ::= { ifEntry 7 } ifOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } ACCESS read-only STATUS mandatory DESCRIPTION "The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed." ::= { ifEntry 8 } ifLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value." ::= { ifEntry 9 } ifInOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets received on the interface, including framing characters." ::= { ifEntry 10 } ifInUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of subnetwork-unicast packets delivered to a higher-layer protocol." ::= { ifEntry 11 } ifInNUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol." ::= { ifEntry 12 } ifInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space." ::= { ifEntry 13 } ifInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol." ::= { ifEntry 14 } ifInUnknownProtos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of packets received via the interface which were discarded because of an unknown or unsupported protocol." ::= { ifEntry 15 } ifOutOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters." ::= { ifEntry 16 } ifOutUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent." ::= { ifEntry 17 } ifOutNUcastPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent." ::= { ifEntry 18 } ifOutDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space." ::= { ifEntry 19 } ifOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of outbound packets that could not be transmitted because of errors." ::= { ifEntry 20 } ifOutQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The length of the output packet queue (in packets)." ::= { ifEntry 21 } ifSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value." ::= { ifEntry 22 } -- the Address Translation group -- Implementation of the Address Translation group is -- mandatory for all systems. Note however that this group -- is deprecated by MIB-II. That is, it is being included -- solely for compatibility with MIB-I nodes, and will most -- likely be excluded from MIB-III nodes. From MIB-II and -- onwards, each network protocol group contains its own -- address translation tables. -- The Address Translation group contains one table which is -- the union across all interfaces of the translation tables -- for converting a NetworkAddress (e.g., an IP address) into -- a subnetwork-specific address. For lack of a better term, -- this document refers to such a subnetwork-specific address -- as a `physical' address. -- Examples of such translation tables are: for broadcast -- media where ARP is in use, the translation table is -- equivalent to the ARP cache; or, on an X.25 network where -- non-algorithmic translation to X.121 addresses is -- required, the translation table contains the -- NetworkAddress to X.121 address equivalences. atTable OBJECT-TYPE SYNTAX SEQUENCE OF AtEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries." ::= { at 1 } atEntry OBJECT-TYPE SYNTAX AtEntry ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry contains one NetworkAddress to `physical' address equivalence." INDEX { atIfIndex, atNetAddress } ::= { atTable 1 } AtEntry ::= SEQUENCE { atIfIndex INTEGER, atPhysAddress PhysAddress, atNetAddress NetworkAddress } atIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS deprecated DESCRIPTION "The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { atEntry 1 } atPhysAddress OBJECT-TYPE SYNTAX PhysAddress ACCESS read-write STATUS deprecated DESCRIPTION "The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object." ::= { atEntry 2 } atNetAddress OBJECT-TYPE SYNTAX NetworkAddress ACCESS read-write STATUS deprecated DESCRIPTION "The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address." ::= { atEntry 3 } -- the IP group -- Implementation of the IP group is mandatory for all -- systems. ipForwarding OBJECT-TYPE SYNTAX INTEGER { forwarding(1), -- acting as a gateway not-forwarding(2) -- NOT acting as a gateway } ACCESS read-write STATUS mandatory DESCRIPTION "The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value." ::= { ip 1 } ipDefaultTTL OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol." ::= { ip 2 } ipInReceives OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of input datagrams received from interfaces, including those received in error." ::= { ip 3 } ipInHdrErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc." ::= { ip 4 } ipInAddrErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address." ::= { ip 5 } ipForwDatagrams OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful." ::= { ip 6 } ipInUnknownProtos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol." ::= { ip 7 } ipInDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly." ::= { ip 8 } ipInDelivers OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of input datagrams successfully delivered to IP user-protocols (including ICMP)." ::= { ip 9 } ipOutRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams." ::= { ip 10 } ipOutDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion." ::= { ip 11 } ipOutNoRoutes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down." ::= { ip 12 } ipReasmTimeout OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity." ::= { ip 13 } ipReasmReqds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP fragments received which needed to be reassembled at this entity." ::= { ip 14 } ipReasmOKs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams successfully re- assembled." ::= { ip 15 } ipReasmFails OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received." ::= { ip 16 } ipFragOKs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams that have been successfully fragmented at this entity." ::= { ip 17 } ipFragFails OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set." ::= { ip 18 } ipFragCreates OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of IP datagram fragments that have been generated as a result of fragmentation at this entity." ::= { ip 19 } -- the IP address table -- The IP address table contains this entity's IP addressing -- information. ipAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IpAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of addressing information relevant to this entity's IP addresses." ::= { ip 20 } ipAddrEntry OBJECT-TYPE SYNTAX IpAddrEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The addressing information for one of this entity's IP addresses." INDEX { ipAdEntAddr } ::= { ipAddrTable 1 } IpAddrEntry ::= SEQUENCE { ipAdEntAddr IpAddress, ipAdEntIfIndex INTEGER, ipAdEntNetMask IpAddress, ipAdEntBcastAddr INTEGER, ipAdEntReasmMaxSize INTEGER (0..65535) } ipAdEntAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address to which this entry's addressing information pertains." ::= { ipAddrEntry 1 } ipAdEntIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { ipAddrEntry 2 } ipAdEntNetMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0." ::= { ipAddrEntry 3 } ipAdEntBcastAddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface." ::= { ipAddrEntry 4 } ipAdEntReasmMaxSize OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface." ::= { ipAddrEntry 5 } -- the IP routing table -- The IP routing table contains an entry for each route -- presently known to this entity. ipRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpRouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This entity's IP Routing table." ::= { ip 21 } ipRouteEntry OBJECT-TYPE SYNTAX IpRouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A route to a particular destination." INDEX { ipRouteDest } ::= { ipRouteTable 1 } IpRouteEntry ::= SEQUENCE { ipRouteDest IpAddress, ipRouteIfIndex INTEGER, ipRouteMetric1 INTEGER, ipRouteMetric2 INTEGER, ipRouteMetric3 INTEGER, ipRouteMetric4 INTEGER, ipRouteNextHop IpAddress, ipRouteType INTEGER, ipRouteProto INTEGER, ipRouteAge INTEGER, ipRouteMask IpAddress, ipRouteMetric5 INTEGER, ipRouteInfo OBJECT IDENTIFIER } ipRouteDest OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use." ::= { ipRouteEntry 1 } ipRouteIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { ipRouteEntry 2 } ipRouteMetric1 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 3 } ipRouteMetric2 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 4 } ipRouteMetric3 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 5 } ipRouteMetric4 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 6 } ipRouteNextHop OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)" ::= { ipRouteEntry 7 } ipRouteType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following invalid(2), -- an invalidated route -- route to directly direct(3), -- connected (sub-)network -- route to a non-local indirect(4) -- host/network/sub-network } ACCESS read-write STATUS mandatory DESCRIPTION "The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object." ::= { ipRouteEntry 8 } ipRouteProto OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following -- non-protocol information, -- e.g., manually configured local(2), -- entries -- set via a network netmgmt(3), -- management protocol -- obtained via ICMP, icmp(4), -- e.g., Redirect -- the remaining values are -- all gateway routing -- protocols egp(5), ggp(6), hello(7), rip(8), is-is(9), es-is(10), ciscoIgrp(11), bbnSpfIgp(12), ospf(13), bgp(14) } ACCESS read-only STATUS mandatory DESCRIPTION "The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols." ::= { ipRouteEntry 9 } ipRouteAge OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned." ::= { ipRouteEntry 10 } ipRouteMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism." ::= { ipRouteEntry 11 } ipRouteMetric5 OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1." ::= { ipRouteEntry 12 } ipRouteInfo OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value." ::= { ipRouteEntry 13 } -- the IP Address Translation table -- The IP address translation table contain the IpAddress to -- `physical' address equivalences. Some interfaces do not -- use translation tables for determining address -- equivalences (e.g., DDN-X.25 has an algorithmic method); -- if all interfaces are of this type, then the Address -- Translation table is empty, i.e., has zero entries. ipNetToMediaTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The IP Address Translation table used for mapping from IP addresses to physical addresses." ::= { ip 22 } ipNetToMediaEntry OBJECT-TYPE SYNTAX IpNetToMediaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Each entry contains one IpAddress to `physical' address equivalence." INDEX { ipNetToMediaIfIndex, ipNetToMediaNetAddress } ::= { ipNetToMediaTable 1 } IpNetToMediaEntry ::= SEQUENCE { ipNetToMediaIfIndex INTEGER, ipNetToMediaPhysAddress PhysAddress, ipNetToMediaNetAddress IpAddress, ipNetToMediaType INTEGER } ipNetToMediaIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex." ::= { ipNetToMediaEntry 1 } ipNetToMediaPhysAddress OBJECT-TYPE SYNTAX PhysAddress ACCESS read-write STATUS mandatory DESCRIPTION "The media-dependent `physical' address." ::= { ipNetToMediaEntry 2 } ipNetToMediaNetAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IpAddress corresponding to the media- dependent `physical' address." ::= { ipNetToMediaEntry 3 } ipNetToMediaType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following invalid(2), -- an invalidated mapping dynamic(3), static(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object." ::= { ipNetToMediaEntry 4 } -- additional IP objects ipRoutingDiscards OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries." ::= { ip 23 } -- the ICMP group -- Implementation of the ICMP group is mandatory for all -- systems. icmpInMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors." ::= { icmp 1 } icmpInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.)." ::= { icmp 2 } icmpInDestUnreachs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Destination Unreachable messages received." ::= { icmp 3 } icmpInTimeExcds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Time Exceeded messages received." ::= { icmp 4 } icmpInParmProbs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Parameter Problem messages received." ::= { icmp 5 } icmpInSrcQuenchs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Source Quench messages received." ::= { icmp 6 } icmpInRedirects OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Redirect messages received." ::= { icmp 7 } icmpInEchos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo (request) messages received." ::= { icmp 8 } icmpInEchoReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo Reply messages received." ::= { icmp 9 } icmpInTimestamps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp (request) messages received." ::= { icmp 10 } icmpInTimestampReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp Reply messages received." ::= { icmp 11 } icmpInAddrMasks OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Request messages received." ::= { icmp 12 } icmpInAddrMaskReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Reply messages received." ::= { icmp 13 } icmpOutMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors." ::= { icmp 14 } icmpOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value." ::= { icmp 15 } icmpOutDestUnreachs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Destination Unreachable messages sent." ::= { icmp 16 } icmpOutTimeExcds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Time Exceeded messages sent." ::= { icmp 17 } icmpOutParmProbs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Parameter Problem messages sent." ::= { icmp 18 } icmpOutSrcQuenchs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Source Quench messages sent." ::= { icmp 19 } icmpOutRedirects OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects." ::= { icmp 20 } icmpOutEchos OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo (request) messages sent." ::= { icmp 21 } icmpOutEchoReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Echo Reply messages sent." ::= { icmp 22 } icmpOutTimestamps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp (request) messages sent." ::= { icmp 23 } icmpOutTimestampReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Timestamp Reply messages sent." ::= { icmp 24 } icmpOutAddrMasks OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Request messages sent." ::= { icmp 25 } icmpOutAddrMaskReps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of ICMP Address Mask Reply messages sent." ::= { icmp 26 } -- the TCP group -- Implementation of the TCP group is mandatory for all -- systems that implement the TCP. -- Note that instances of object types that represent -- information about a particular TCP connection are -- transient; they persist only as long as the connection -- in question. tcpRtoAlgorithm OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following constant(2), -- a constant rto rsre(3), -- MIL-STD-1778, Appendix B vanj(4) -- Van Jacobson's algorithm [10] } ACCESS read-only STATUS mandatory DESCRIPTION "The algorithm used to determine the timeout value used for retransmitting unacknowledged octets." ::= { tcp 1 } tcpRtoMin OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793." ::= { tcp 2 } tcpRtoMax OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793." ::= { tcp 3 } tcpMaxConn OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1." ::= { tcp 4 } tcpActiveOpens OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state." ::= { tcp 5 } tcpPassiveOpens OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state." ::= { tcp 6 } tcpAttemptFails OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state." ::= { tcp 7 } tcpEstabResets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state." ::= { tcp 8 } tcpCurrEstab OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT." ::= { tcp 9 } tcpInSegs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments received, including those received in error. This count includes segments received on currently established connections." ::= { tcp 10 } tcpOutSegs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets." ::= { tcp 11 } tcpRetransSegs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets." ::= { tcp 12 } -- the TCP Connection table -- The TCP connection table contains information about this -- entity's existing TCP connections. tcpConnTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpConnEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing TCP connection-specific information." ::= { tcp 13 } tcpConnEntry OBJECT-TYPE SYNTAX TcpConnEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state." INDEX { tcpConnLocalAddress, tcpConnLocalPort, tcpConnRemAddress, tcpConnRemPort } ::= { tcpConnTable 1 } TcpConnEntry ::= SEQUENCE { tcpConnState INTEGER, tcpConnLocalAddress IpAddress, tcpConnLocalPort INTEGER (0..65535), tcpConnRemAddress IpAddress, tcpConnRemPort INTEGER (0..65535) } tcpConnState OBJECT-TYPE SYNTAX INTEGER { closed(1), listen(2), synSent(3), synReceived(4), established(5), finWait1(6), finWait2(7), closeWait(8), lastAck(9), closing(10), timeWait(11), deleteTCB(12) } ACCESS read-write STATUS mandatory DESCRIPTION "The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably)." ::= { tcpConnEntry 1 } tcpConnLocalAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used." ::= { tcpConnEntry 2 } tcpConnLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The local port number for this TCP connection." ::= { tcpConnEntry 3 } tcpConnRemAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The remote IP address for this TCP connection." ::= { tcpConnEntry 4 } tcpConnRemPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The remote port number for this TCP connection." ::= { tcpConnEntry 5 } -- additional TCP objects tcpInErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of segments received in error (e.g., bad TCP checksums)." ::= { tcp 14 } tcpOutRsts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of TCP segments sent containing the RST flag." ::= { tcp 15 } -- the UDP group -- Implementation of the UDP group is mandatory for all -- systems which implement the UDP. udpInDatagrams OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of UDP datagrams delivered to UDP users." ::= { udp 1 } udpNoPorts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of received UDP datagrams for which there was no application at the destination port." ::= { udp 2 } udpInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port." ::= { udp 3 } udpOutDatagrams OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of UDP datagrams sent from this entity." ::= { udp 4 } -- the UDP Listener table -- The UDP listener table contains information about this -- entity's UDP end-points on which a local application is -- currently accepting datagrams. udpTable OBJECT-TYPE SYNTAX SEQUENCE OF UdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing UDP listener information." ::= { udp 5 } udpEntry OBJECT-TYPE SYNTAX UdpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a particular current UDP listener." INDEX { udpLocalAddress, udpLocalPort } ::= { udpTable 1 } UdpEntry ::= SEQUENCE { udpLocalAddress IpAddress, udpLocalPort INTEGER (0..65535) } udpLocalAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used." ::= { udpEntry 1 } udpLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The local port number for this UDP listener." ::= { udpEntry 2 } -- the EGP group -- Implementation of the EGP group is mandatory for all -- systems which implement the EGP. egpInMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP messages received without error." ::= { egp 1 } egpInErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP messages received that proved to be in error." ::= { egp 2 } egpOutMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of locally generated EGP messages." ::= { egp 3 } egpOutErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of locally generated EGP messages not sent due to resource limitations within an EGP entity." ::= { egp 4 } -- the EGP Neighbor table -- The EGP neighbor table contains information about this -- entity's EGP neighbors. egpNeighTable OBJECT-TYPE SYNTAX SEQUENCE OF EgpNeighEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The EGP neighbor table." ::= { egp 5 } egpNeighEntry OBJECT-TYPE SYNTAX EgpNeighEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about this entity's relationship with a particular EGP neighbor." INDEX { egpNeighAddr } ::= { egpNeighTable 1 } EgpNeighEntry ::= SEQUENCE { egpNeighState INTEGER, egpNeighAddr IpAddress, egpNeighAs INTEGER, egpNeighInMsgs Counter, egpNeighInErrs Counter, egpNeighOutMsgs Counter, egpNeighOutErrs Counter, egpNeighInErrMsgs Counter, egpNeighOutErrMsgs Counter, egpNeighStateUps Counter, egpNeighStateDowns Counter, egpNeighIntervalHello INTEGER, egpNeighIntervalPoll INTEGER, egpNeighMode INTEGER, egpNeighEventTrigger INTEGER } egpNeighState OBJECT-TYPE SYNTAX INTEGER { idle(1), acquisition(2), down(3), up(4), cease(5) } ACCESS read-only STATUS mandatory DESCRIPTION "The EGP state of the local system with respect to this entry's EGP neighbor. Each EGP state is represented by a value that is one greater than the numerical value associated with said state in RFC 904." ::= { egpNeighEntry 1 } egpNeighAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of this entry's EGP neighbor." ::= { egpNeighEntry 2 } egpNeighAs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The autonomous system of this EGP peer. Zero should be specified if the autonomous system number of the neighbor is not yet known." ::= { egpNeighEntry 3 } egpNeighInMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP messages received without error from this EGP peer." ::= { egpNeighEntry 4 } egpNeighInErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP messages received from this EGP peer that proved to be in error (e.g., bad EGP checksum)." ::= { egpNeighEntry 5 } egpNeighOutMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of locally generated EGP messages to this EGP peer." ::= { egpNeighEntry 6 } egpNeighOutErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of locally generated EGP messages not sent to this EGP peer due to resource limitations within an EGP entity." ::= { egpNeighEntry 7 } egpNeighInErrMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP-defined error messages received from this EGP peer." ::= { egpNeighEntry 8 } egpNeighOutErrMsgs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP-defined error messages sent to this EGP peer." ::= { egpNeighEntry 9 } egpNeighStateUps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP state transitions to the UP state with this EGP peer." ::= { egpNeighEntry 10 } egpNeighStateDowns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of EGP state transitions from the UP state to any other state with this EGP peer." ::= { egpNeighEntry 11 } egpNeighIntervalHello OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The interval between EGP Hello command retransmissions (in hundredths of a second). This represents the t1 timer as defined in RFC 904." ::= { egpNeighEntry 12 } egpNeighIntervalPoll OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The interval between EGP poll command retransmissions (in hundredths of a second). This represents the t3 timer as defined in RFC 904." ::= { egpNeighEntry 13 } egpNeighMode OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The polling mode of this EGP entity, either passive or active." ::= { egpNeighEntry 14 } egpNeighEventTrigger OBJECT-TYPE SYNTAX INTEGER { start(1), stop(2) } ACCESS read-write STATUS mandatory DESCRIPTION "A control variable used to trigger operator- initiated Start and Stop events. When read, this variable always returns the most recent value that egpNeighEventTrigger was set to. If it has not been set since the last initialization of the network management subsystem on the node, it returns a value of `stop'. When set, this variable causes a Start or Stop event on the specified neighbor, as specified on pages 8-10 of RFC 904. Briefly, a Start event causes an Idle peer to begin neighbor acquisition and a non-Idle peer to reinitiate neighbor acquisition. A stop event causes a non-Idle peer to return to the Idle state until a Start event occurs, either via egpNeighEventTrigger or otherwise." ::= { egpNeighEntry 15 } -- additional EGP objects egpAs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The autonomous system number of this EGP entity." ::= { egp 6 } -- the Transmission group -- Based on the transmission media underlying each interface -- on a system, the corresponding portion of the Transmission -- group is mandatory for that system. -- When Internet-standard definitions for managing -- transmission media are defined, the transmission group is -- used to provide a prefix for the names of those objects. -- Typically, such definitions reside in the experimental -- portion of the MIB until they are "proven", then as a -- part of the Internet standardization process, the -- definitions are accordingly elevated and a new object -- identifier, under the transmission group is defined. By -- convention, the name assigned is: -- -- type OBJECT IDENTIFIER ::= { transmission number } -- -- where "type" is the symbolic value used for the media in -- the ifType column of the ifTable object, and "number" is -- the actual integer value corresponding to the symbol. -- the SNMP group -- Implementation of the SNMP group is mandatory for all -- systems which support an SNMP protocol entity. Some of -- the objects defined below will be zero-valued in those -- SNMP implementations that are optimized to support only -- those functions specific to either a management agent or -- a management station. In particular, it should be -- observed that the objects below refer to an SNMP entity, -- and there may be several SNMP entities residing on a -- managed node (e.g., if the node is hosting acting as -- a management station). snmpInPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of Messages delivered to the SNMP entity from the transport service." ::= { snmp 1 } snmpOutPkts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service." ::= { snmp 2 } snmpInBadVersions OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version." ::= { snmp 3 } snmpInBadCommunityNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity." ::= { snmp 4 } snmpInBadCommunityUses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message." ::= { snmp 5 } snmpInASNParseErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages." ::= { snmp 6 } -- { snmp 7 } is not used in rfc1213, but MIBII.mdl had one :( snmpInBadTypes OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Total number of PDUs having an unknown PDU type" ::= { snmp 7 } snmpInTooBigs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'." ::= { snmp 8 } snmpInNoSuchNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'." ::= { snmp 9 } snmpInBadValues OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'." ::= { snmp 10 } snmpInReadOnlys OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP." ::= { snmp 11 } snmpInGenErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'." ::= { snmp 12 } snmpInTotalReqVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs." ::= { snmp 13 } snmpInTotalSetVars OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs." ::= { snmp 14 } snmpInGetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 15 } snmpInGetNexts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 16 } snmpInSetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 17 } snmpInGetResponses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 18 } snmpInTraps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity." ::= { snmp 19 } snmpOutTooBigs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.'" ::= { snmp 20 } snmpOutNoSuchNames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'." ::= { snmp 21 } snmpOutBadValues OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'." ::= { snmp 22 } -- { snmp 23 } is not used in rfc1213, but MIBII.mdl had one :( snmpOutReadOnlys OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `readOnly'." ::= { snmp 23 } snmpOutGenErrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'." ::= { snmp 24 } snmpOutGetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity." ::= { snmp 25 } snmpOutGetNexts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity." ::= { snmp 26 } snmpOutSetRequests OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity." ::= { snmp 27 } snmpOutGetResponses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity." ::= { snmp 28 } snmpOutTraps OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity." ::= { snmp 29 } snmpEnableAuthenTraps OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system." ::= { snmp 30 } END -- @(#)WSCCS g/mibs-wfcommon.mib 1.4 10/26/95 Wellfleet-COMMON-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI; wellfleet OBJECT IDENTIFIER ::= { enterprises 18 } wfSwSeries7 OBJECT IDENTIFIER ::= { wellfleet 3 } wfHardwareConfig OBJECT IDENTIFIER ::= { wfSwSeries7 1 } wfHwModuleGroup OBJECT IDENTIFIER ::= { wfHardwareConfig 4 } wfSystem OBJECT IDENTIFIER ::= { wfSwSeries7 3 } END -- Wellfleet-COMMON-MIB -- @(#)WSCCS i/mibs-hardware.mib 1.2 10/9/95 Wellfleet-HARDWARE-MIB DEFINITIONS ::= BEGIN -- Created by mdl2asn version 3.1 -- Creation date: Wed Aug 30 16:42:01 EDT 1995 IMPORTS IpAddress, Counter, Gauge, TimeTicks, Opaque, enterprises, mgmt FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 DisplayString, mib-2 FROM RFC1213-MIB wfHardwareConfig FROM Wellfleet-COMMON-MIB; wfHwBase OBJECT IDENTIFIER ::= { wfHardwareConfig 1 } wfHwBpIdOpt OBJECT-TYPE SYNTAX INTEGER { acefn(1), aceln(2), acecn(3), afn(4), in(5), an(16), sys5000(5000), freln(16640), frecn(16896), frerbln(17152), asn(20480), asnzcable(20736), asnbcable(20992) } ACCESS read-only STATUS mandatory DESCRIPTION "The BackPlane identification number." ::= { wfHwBase 1 } wfHwBpRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the BackPlane. High byte is in upper 2 bytes." ::= { wfHwBase 2 } wfHwBpSerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the BackPlane." ::= { wfHwBase 3 } wfBCNPwrSupply1 OBJECT-TYPE SYNTAX INTEGER { ok(1), fail(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of BCN Hot-Swappable Power Supply 1" DEFVAL { notpresent } ::= { wfHwBase 4 } wfBCNPwrSupply2 OBJECT-TYPE SYNTAX INTEGER { ok(1), fail(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of BCN Hot-Swappable Power Supply 2" DEFVAL { notpresent } ::= { wfHwBase 5 } wfBCNPwrSupply3 OBJECT-TYPE SYNTAX INTEGER { ok(1), fail(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of BCN Hot-Swappable Power Supply 3" DEFVAL { notpresent } ::= { wfHwBase 6 } wfBCNPwrSupply4 OBJECT-TYPE SYNTAX INTEGER { ok(1), fail(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of BCN Hot-Swappable Power Supply 4" DEFVAL { notpresent } ::= { wfHwBase 7 } wfBCNFanStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), fail(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of BCN Fan Tray" DEFVAL { notpresent } ::= { wfHwBase 8 } wfBCNTemperature OBJECT-TYPE SYNTAX INTEGER { ok(1), caution(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of BCN Temperature sensor" DEFVAL { notpresent } ::= { wfHwBase 9 } wfHwTable OBJECT-TYPE SYNTAX SEQUENCE OF WfHwEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Hardware Table - indexed by slot number" ::= { wfHardwareConfig 2 } wfHwEntry OBJECT-TYPE SYNTAX WfHwEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Hardware specific information about a slot." INDEX { wfHwSlot } ::= { wfHwTable 1 } WfHwEntry ::= SEQUENCE { wfHwSlot INTEGER, wfHwModIdOpt INTEGER, wfHwModRev OCTET STRING, wfHwModSerialNumber OCTET STRING, wfHwMotherBdIdOpt INTEGER, wfHwMotherBdRev OCTET STRING, wfHwMotherBdSerialNumber OCTET STRING, wfHwDaughterBdIdOpt INTEGER, wfHwDaughterBdRev OCTET STRING, wfHwDaughterBdSerialNumber OCTET STRING, wfHwBabyBdIdOpt INTEGER, wfHwBabyBdRev OCTET STRING, wfHwBabyBdSerialNumber OCTET STRING, wfHwDiagPromRev OCTET STRING, wfHwDiagPromDate DisplayString, wfHwDiagPromSource DisplayString, wfHwBootPromRev OCTET STRING, wfHwBootPromDate DisplayString, wfHwBootPromSource DisplayString, wfHwSparePromRev OCTET STRING, wfHwSparePromDate DisplayString, wfHwSparePromSource DisplayString, wfHwFileSysPresent INTEGER, wfHwFileSysPresent2 INTEGER, wfHwConfigServer INTEGER, wfHwConfigFile DisplayString, wfHwConfigDateAndTime OCTET STRING, wfHwActiveImageName DisplayString, wfHwActiveImageSource DisplayString, wfHwActiveImageDate DisplayString, wfHwMotherBdMemorySize INTEGER, wfHwFastPacketCacheSize INTEGER, wfHwModDaughterBd1IdOpt INTEGER, wfHwModDaughterBd1AwRev OCTET STRING, wfHwModDaughterBd1Rev OCTET STRING, wfHwModDaughterBd1SerialNumber OCTET STRING, wfHwModDaughterBd2IdOpt INTEGER, wfHwModDaughterBd2AwRev OCTET STRING, wfHwModDaughterBd2Rev OCTET STRING, wfHwModDaughterBd2SerialNumber OCTET STRING } wfHwSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each slot. Its value ranges between 1 and 14. There are products in this family that contain 1, 5, and 14 slots." ::= { wfHwEntry 1 } wfHwModIdOpt OBJECT-TYPE SYNTAX INTEGER { enet1(1), enet2(8), sync1(16), sync1a(17), t11(24), dse1(32), dse1a(33), dst416(40), sst416a(41), dst4(42), sst4a(43), sst416(44), stok416(45), sst4(46), stok4(47), floppy(48), necfloppy(49), t12(56), t12a(57), st1(58), t156k(60), e1(61), st156k(62), se1(63), t12n(64), st1n(65), t156kn(66), st156kn(67), e1n(68), se1n(69), sync(80), sync2a(81), cmcfddi(88), iphfddi(89), dt(104), dsde1(112), dsde1a(113), enet(114), dse2(116), dse2a(117), sse(118), ssea(119), dsde10bt(120), enet3(132), dsde2(156), oldqenf(160), denf(161), qenf(162), qef(164), def(165), mct1(168), smct1(169), dtok(176), mce1(184), smce1(185), mce1ii75(188), smce1ii75(189), mce1ii120(190), smce1ii120(191), wffddi2m(192), wffddi1m(193), wffddi2s(194), wffddi1s(195), wffddi2mf(196), wffddi1mf(197), wffddi2sf(198), wffddi1sf(199), fmdset(200), fmdst(201), fmdse(202), fmsst(203), fmsse(204), fnsdse(208), fnsdsdt(216), fnsdst(217), dhssi(224), shssi(225), esafnf(232), esafdsenf(233), esafssenf(234), esafdenf(235), esaf(236), esafdse(237), esafsse(238), esafde(239), qtok(256), asn(511), anseds(1024), ansedst(1025), ansedsh(1026), ansedsi(1027), ansedsti(1028), ansedshi(1029), ansets(1030), ansetst(1031), ansetsh(1032), andeds(1033), andedst(1034), andedsh(1035), andstx(1036), andst(1037), andsti(1038), antst(1039), antstx(1040), ansdsedst(1041), ansdsedstx(1042), ansedsi2(1043), ansedsti2(1044), ansedshi2(1045), andsti2(1046), ansedsg(1047), ansedsgx(1048), ansetsg(1049), andedsg(1050), ansedsgi(1051), ansetsgx(1052), andedsgx(1053), ansedsgix(1054), ansedsx(1055), ansetsx(1056), andedsx(1057), ansedstx(1058), ansetstx(1059), andedstx(1060), andsti2x(1061), ansedsi2x(1062), ansedsti2x(1063), atmalc(4096), atmalctaxi100(4097), atmalcsonetmm(4098), atmalcsonetsm(4099), osync(4352), comp(4353), comp128(4354), atmcoc3mm(4608), atmcoc3sm(4609), atmcoc3utp5(4610), de100(4864), atmcds3(5120), atmce3(5121), qmct1rj45(5376), qmct1db15(5377), srml(8448), atm5000ah(524288), qe(1048799), qehwf(1048798), qefddi2m(1048831), qefddi2mhwf(1048830), qefddi2s(1048823), qefddi2shwf(1048822), qefddi1m(1048815), qefddi1mhwf(1048814), qefddi1s(1048807), qefddi1shwf(1048806), qecddi2stp(1048827), qecddi2stphwf(1048826), qecddi1stp(1048811), qecddi1stphwf(1048810), qecddi2utp(1048763), qecddi2utphwf(1048762), qecddi1utp(1048747), qecddi1utphwf(1048746), enet3atm(1048832), enet3enet(1048833), enet3fddi(1048834), enet3tok(1048835), enet3tokf(1048836), enet3sync(1048837), enet3only(1048863), fddiatm(1048864), fddienet(1048865), fddifddi(1048866), fdditok(1048867), fdditokf(1048868), fddisync(1048869), fddionly(1048895), tok3atm(1048896), tok3enet(1048897), tok3fddi(1048898), tok3tok(1048899), tok3tokf(1048900), tok3sync(1048901), tok3only(1048927), tokf3atm(1048928), tokf3enet(1048929), tokf3fddi(1048930), tokf3tok(1048931), tokf3tokf(1048932), tokf3sync(1048933), tokf3only(1048959), enet3datm(1048960), enet3denet(1048961), enet3dfddi(1048962), enet3dtok(1048963), enet3dtokf(1048964), enet3dsync(1048965), enet3donly(1048991), chipcomfenet(1049089), chipcomffddi(1049090), chipcomftok(1049091), chipcomftokf(1049092), chipcomfdsync(1049093), chipcomfisdn(1049094), chipcomffddis(1049095), chipcomfonly(1049119), chipcomenet(1049217), chipcomfddi(1049218), chipcomtok(1049219), chipcomtokf(1049220), chipcomdsync(1049221), chipcomisdn(1049222), chipcomfddis(1049223), chipcomonly(1049247) } ACCESS read-only STATUS mandatory DESCRIPTION "The module identification number. Port Configurations HWStat Name Enet Sync Async Token Framer Fiber ------ ------------ ------ ---- ----- ----- ------ ----- 1 ENET-1 2 0 0 0 0 0 8 ENET-2 2 0 0 0 0 0 16 SYNC-1 0 4 1 0 0 0 17 SYNC-1 [1] 0 4 1 0 0 0 24 T1-1 0 2 1 0 2 0 32 DSE-1 1 2 1 0 0 0 33 DSE-1 [1] 1 2 1 0 0 0 40 DST-4/16 0 2 1 1 0 0 41 SST-4/16 [1] 0 1 1 1 0 0 42 DST-4 0 2 1 1 0 0 43 SST-4 [1] 0 1 1 1 0 0 44 SST-4/16 0 1 1 1 0 0 45 STOK-4/16 [3] 0 0 0 1 0 0 46 SST-4 0 1 1 1 0 0 47 STOK-4 [3] 0 0 0 1 0 0 48 FLOPPY 0 0 0 0 0 0 56 T1-2 0 2 1 0 2 0 57 T1-2 0 2 1 0 2 0 58 ST1 0 1 1 0 1 0 60 T1-56K 0 1 1 0 1 0 61 E1 [3] 0 2 0 0 2 0 62 ST1-56K 0 1 1 0 1 0 63 SE1 [3] 0 1 0 0 1 0 64 T1-2n 0 2 1 0 2 0 65 ST1n 0 1 1 0 1 0 66 T1-56Kn 0 1 1 0 1 0 67 ST1-56Kn 0 1 1 0 1 0 68 E1n [3] 0 2 0 0 2 0 69 SE1n [3] 0 1 0 0 1 0 80 SYNC-2 0 4 1 0 0 0 81 SYNC-2 [1] 0 4 1 0 0 0 88 CMC-FDDI [6] 0 0 0 0 0 1 89 IPHASE-FDDI [6] 0 0 0 0 0 1 112 DSDE-1 2 2 1 0 0 0 113 DSDE-1 [1] 2 2 1 0 0 0 114 ENET 2 0 0 0 0 0 116 DSE-2 1 2 1 0 0 0 117 DSE-2 [1] 1 2 1 0 0 0 118 SSE 1 1 1 0 0 0 119 SSE [1] 1 1 1 0 0 0 132 ENET-3 [2] 2 0 0 0 0 0 156 DSDE-2 [2] 2 2 1 0 0 0 160 QE/NF 4 0 0 0 0 0 161 DE/NF [5] 2 0 0 0 0 0 162 QE/NF 4 0 0 0 0 0 164 QE/F [4] 4 0 0 0 0 0 165 DE/F [4,5] 2 0 0 0 0 0 168 MCT1 0 2 Munich 0 0 2 0 169 SMCT1 0 1 Munich 0 0 1 0 176 DTOK 0 0 0 2 0 0 184 MCE1 0 2 Munich 0 0 2 0 185 SMCE1 0 1 Munich 0 0 1 0 188 MCE1II75 0 2 Munich 0 0 2 0 189 SMCE1II75 0 1 Munich 0 0 1 0 190 MCE1II120 0 2 Munich 0 0 2 0 191 SMCE1II120 0 1 Munich 0 0 1 0 192 WF_FDDI_2M 0 0 0 0 0 1 193 WF_FDDI_1M 0 0 0 0 0 1 194 WF_FDDI_2S 0 0 0 0 0 1 195 WF_FDDI_1S 0 0 0 0 0 1 196 WF_FDDI_2MF 0 0 0 0 0 1 197 WF_FDDI_1MF 0 0 0 0 0 1 198 WF_FDDI_2SF 0 0 0 0 0 1 199 WF_FDDI_1SF 0 0 0 0 0 1 200 HW_MODULE_FMDSET [7] 1 2 0 1 0 0 201 HW_MODULE_FMDST [7] 0 2 0 1 0 0 202 HW_MODULE_FMDSE [7] 1 2 0 0 0 0 203 HW_MODULE_FMSST [7] 0 1 0 1 0 0 204 HW_MODULE_FMSSE [7] 1 1 0 0 0 0 208 FNSDSE [7] 1 2 0 0 0 0 216 FNSDSDT [7] 0 2 0 2 0 0 217 FNSDST [7] 0 2 0 1 0 0 224 DHSSI 0 2 hssi 0 0 0 0 225 SHSSI 0 1 hssi 0 0 0 0 232 ESAF_NF 2 2 0 0 0 0 233 ESAF_DSE_NF 1 2 0 0 0 0 234 ESAF_SSE_NF 1 1 0 0 0 0 235 ESAF_DE_NF 2 0 0 0 0 0 236 ESAF [2] 2 2 0 0 0 0 237 ESAF_DSE [2] 1 2 0 0 0 0 238 ESAF_SSE [2] 1 1 0 0 0 0 239 ESAF_DE [2] 2 0 0 0 0 0 256 QTOK 0 0 0 4 0 0 ASN (Barracuda) 511 ASN[8] AN Module IDs (Piranha, Guppy...) ID Mnemonic ENET SYNC ISDN TR HUB DCM -- -------- ---- ---- ---- -- --- --- 1024 ANSEDS 1 2 0 0 0 N 1025 ANSEDST 1 2 0 1 0 N 1026 ANSEDSH 1 2 0 0 12 N 1027 ANSEDSI 1 2 1 0 0 N 1028 ANSEDSTI 1 2 1 1 0 N 1029 ANSEDSHI 1 2 1 0 12 N 1030 ANSETS 1 3 0 0 0 N 1031 ANSETST 1 3 0 1 0 N 1032 ANSETSH 1 3 0 0 12 N 1033 ANDEDS 2 2 0 0 0 N 1034 ANDEDST 2 2 0 1 0 N 1035 ANDEDSH 2 2 0 0 12 N 1036 ANDSTX 0 2 0 1 0 Y (formerly ANDS) 1037 ANDST 0 2 0 1 0 N 1038 ANDSTI 0 2 1 1 0 N 1039 ANTST 0 3 0 1 0 N 1040 ANTSTX 0 3 0 1 0 Y (formerly ANSDSEDS) 1041 ANSDSEDST 1 2 0 1 0 N 1042 ANSDSEDSTX 1 2 0 1 0 Y (formerly ANSDSEDSH) 1043 ANSEDSI2 1 2 1 0 0 N 1044 ANSEDSTI2 1 2 1 1 0 N 1045 ANSEDSHI2 1 2 1 0 12 N 1046 ANDSTI2 0 2 1 1 0 N 1047 ANSEDSG 1 2 0 0 8 N 1048 ANSEDSGX 1 2 0 0 8 Y 1049 ANSETSG 1 3 0 0 8 N 1050 ANDEDSG 2 2 0 0 8 N 1051 ANSEDSGI 1 2 1 0 8 N 1052 ANSETSGX 1 3 0 0 8 Y 1053 ANDEDSGX 2 2 0 0 8 Y 1054 ANSEDSGIX 1 2 1 0 8 Y 1055 ANSEDSX 1 2 0 0 0 Y 1056 ANSETSX 1 3 0 0 0 Y 1057 ANDEDSX 2 2 0 0 0 Y 1058 ANSEDSTX 1 2 0 1 0 Y 1059 ANSETSTX 1 3 0 1 0 Y 1060 ANDEDSTX 2 2 0 1 0 Y 1061 ANDSTI2X 0 2 1 0 0 Y 1062 ANSEDSI2X 1 2 1 0 0 Y 1063 ANSEDSTI2X 1 2 1 1 0 Y 4096 ATMALC 0 0 0 0 0 0 4097 ATMALCTAXI100 0 0 0 0 0 1 4098 ATMALCSONETMM 0 0 0 0 1 1 [9] 4099 ATMALCSONETSM 0 0 0 0 1 1 [9] 4352 OSYNC 0 8 0 0 0 0 4353 OSYNC_COMP (32) 0 8 0 0 0 0 4354 OSYNC_COMP128 0 8 0 0 0 0 4608 ATMCOC3MM 0 0 0 0 1 1 [10] 4609 ATMCOC3SM 0 0 0 0 1 1 [10] 4610 ATMCOC3UTP5 0 0 0 0 1 0 [10] 4864 DE100 2 0 0 0 0 0 5120 ATMCDS3 0 0 0 0 1 0 [10] 5121 ATMCE3 0 0 0 0 1 0 [10] 8448 SRML 0 0 0 0 0 0 NOTES: [1] Indicates Module has COM Port 1 configured for ASYNC. The AM8530's port B is configured for COM1. [2] This Module contains the DEFA - Hardware Filtering. CAMS must be programmed (can contain 2 - 6 CAMS onboard). [3] The AM8530 has been removed (depopulated) from this module. Programming this device should not be performed. [4] Contains Dual Defa hardware. (Can be depopulated) [5] Depop'd two ports of hardware to make Dual Ethernet module. [6] These are FDDI modules. The ID cannot be read from the Link module I/O space. [7] These are AFN Platform Integrated 'Modules' - Cannot be detached or be used by any other platform. [8] Module IDs from 1280(0x500) to 2559(0x9ff) are used for the ASN Net Modules. Module ID 512(0x200) is used for the ASN SPEX. These IDs are documented in MODULE.mdl. A module ID of 511(0x1ff) in 'wfHwEntry.wfHwModIdOpt' indicates that it is an ASN platform and the user should refer to 'wfHwModuleEntry.wfHwModuleModIdOpt' for Module ID details [9] ATMALC link modules. The physical option for SONET includes a framer and the medium is fiber optics. Only one port per physical daughtercard per link module. [10] ARE UTOPIA link modules. " ::= { wfHwEntry 2 } wfHwModRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the module. High byte is in upper 2 bytes." ::= { wfHwEntry 3 } wfHwModSerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the module." ::= { wfHwEntry 4 } wfHwMotherBdIdOpt OBJECT-TYPE SYNTAX INTEGER { sysctrl(1), ace12(2), ace25(3), ace32(4), afn(5), in(6), sysctrl2(7), an(16), fre(256), fre2(768), o60(769), asn(1024), are(1280), srmf(8704) } ACCESS read-only STATUS mandatory DESCRIPTION "The mother board identification number." ::= { wfHwEntry 5 } wfHwMotherBdRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the mother board. High byte is in upper 2 bytes." ::= { wfHwEntry 6 } wfHwMotherBdSerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the mother board." ::= { wfHwEntry 7 } wfHwDaughterBdIdOpt OBJECT-TYPE SYNTAX INTEGER { sysctrl(1), ace68020mhz12(2), ace68020mhz25(3), ace68030mhz32(4), fre68040mhz25(4352), fre68040mhz33(4608) } ACCESS read-only STATUS mandatory DESCRIPTION "The daughter board identification number." ::= { wfHwEntry 8 } wfHwDaughterBdRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the daughter board. High byte is in upper 2 bytes." ::= { wfHwEntry 9 } wfHwDaughterBdSerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the daughter board." ::= { wfHwEntry 10 } wfHwBabyBdIdOpt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The baby board identification number." ::= { wfHwEntry 11 } wfHwBabyBdRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the baby board. High byte is in upper 2 bytes." ::= { wfHwEntry 12 } wfHwBabyBdSerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the baby board." ::= { wfHwEntry 13 } wfHwDiagPromRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the Diagnostic PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes." ::= { wfHwEntry 14 } wfHwDiagPromDate OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The creation date of the Diagnostic PROM" ::= { wfHwEntry 15 } wfHwDiagPromSource OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The origin of the Diagnostic PROM contents" ::= { wfHwEntry 16 } wfHwBootPromRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the BOOT PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes." ::= { wfHwEntry 17 } wfHwBootPromDate OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The creation date of the Boot PROM" ::= { wfHwEntry 18 } wfHwBootPromSource OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The origin of the Boot PROM contents" ::= { wfHwEntry 19 } wfHwSparePromRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the BOOT PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes." ::= { wfHwEntry 20 } wfHwSparePromDate OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The creation date of the Spare PROM" ::= { wfHwEntry 21 } wfHwSparePromSource OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The origin of the Spare PROM contents" ::= { wfHwEntry 22 } wfHwFileSysPresent OBJECT-TYPE SYNTAX INTEGER { filesys(1), nofilesys(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Flag indicating presence of File System on this slot." DEFVAL { nofilesys } ::= { wfHwEntry 23 } wfHwFileSysPresent2 OBJECT-TYPE SYNTAX INTEGER { filesys(1), nofilesys(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Flag indicating presence of File System (Syscon2 volume#2) on this slot." DEFVAL { nofilesys } ::= { wfHwEntry 24 } wfHwConfigServer OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The slot number from which this slot was served its configuration. If the value for this attribute is 0, this slot obtained its configuration from a file system resource (not necessarily local); If the value for this attribute is -1, this slot does not participate in the boot process (e.g. SRM). A positive value indicates that the configuration was obtained from memory from the slot indicated by the value of this attribute." ::= { wfHwEntry 25 } wfHwConfigFile OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The name of the config file the active configuration was derived from. This does NOT necessarily reflect the current configuration!" ::= { wfHwEntry 26 } wfHwConfigDateAndTime OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The 11 octet date and time that a configuration was loaded on/served to this slot. Octet map: 1-2 Year, 3 Month, 4 Day, 5 Hour, 6 Minutes, 7 Seconds, 8 Deci-seconds, 9 Direction from GMT ('+'|`-'), 10 GMT Hour Offset, 11 GMT Minute Offset." ::= { wfHwEntry 27 } wfHwActiveImageName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "If slot was booted from a local source: this is the name of the active image, which is in the form of :. If slot was booted from a network source: this is the full pathname where the active image was found on the remote server." ::= { wfHwEntry 28 } wfHwActiveImageSource OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The origin of the active image" ::= { wfHwEntry 29 } wfHwActiveImageDate OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The date which the active image was created" ::= { wfHwEntry 30 } wfHwMotherBdMemorySize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The total installed dram size in kilobytes." ::= { wfHwEntry 31 } wfHwFastPacketCacheSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The size of the installed fast packet cache in kilobytes." ::= { wfHwEntry 32 } wfHwModDaughterBd1IdOpt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #1 identification number" ::= { wfHwEntry 33 } wfHwModDaughterBd1AwRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #1 artwork revision level" ::= { wfHwEntry 34 } wfHwModDaughterBd1Rev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #1 board revision level" ::= { wfHwEntry 35 } wfHwModDaughterBd1SerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #1 serial number" ::= { wfHwEntry 36 } wfHwModDaughterBd2IdOpt OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #2 identification number" ::= { wfHwEntry 37 } wfHwModDaughterBd2AwRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #2 artwork revision level" ::= { wfHwEntry 38 } wfHwModDaughterBd2Rev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #2 board revision level" ::= { wfHwEntry 39 } wfHwModDaughterBd2SerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Link module daughter board #2 serial number" ::= { wfHwEntry 40 } END -- Wellfleet-HARDWARE-MIB -- @(#)WSCCS q/mibs-module.mib 1.1 8/30/95 Wellfleet-MODULE-MIB DEFINITIONS ::= BEGIN -- Created by mdl2asn version 3.1 -- Creation date: Wed Aug 30 16:45:27 EDT 1995 IMPORTS IpAddress, Counter, Gauge, TimeTicks, Opaque, enterprises, mgmt FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 DisplayString, mib-2 FROM RFC1213-MIB wfHwModuleGroup FROM Wellfleet-COMMON-MIB; wfHwModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF WfHwModuleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Hardware Module Table Filled in by the Module Driver. Read by SNMP to build the driver load records " ::= { wfHwModuleGroup 1 } wfHwModuleEntry OBJECT-TYPE SYNTAX WfHwModuleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Hardware specific information about a slot." INDEX { wfHwModuleSlot, wfHwModuleModule } ::= { wfHwModuleTable 1 } WfHwModuleEntry ::= SEQUENCE { wfHwModuleSlot INTEGER, wfHwModuleModule INTEGER, wfHwModuleModIdOpt INTEGER, wfHwModuleModRev OCTET STRING, wfHwModuleModSerialNumber OCTET STRING, wfHwModuleArtworkRev DisplayString } wfHwModuleSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each slot. Its value ranges between 1 and 4." ::= { wfHwModuleEntry 1 } wfHwModuleModule OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This value ranges between 1 and 4" ::= { wfHwModuleEntry 2 } wfHwModuleModIdOpt OBJECT-TYPE SYNTAX INTEGER { spex(512), hss(768), hsd(769), denm(1280), denmhwf(1281), dsnmnn(1536), dsnmn1(1537), dsnmn2(1538), dsnm1n(1540), dsnm11(1541), dsnm12(1542), dsnm2n(1544), dsnm21(1545), dsnm22(1546), dsnmnnisdn(1584), dsnmn1isdn(1585), dsnmn2isdn(1586), dsnm1nisdn(1588), dsnm11isdn(1589), dsnm12isdn(1590), dsnm2nisdn(1592), dsnm21isdn(1593), dsnm22isdn(1594), mmfsdsas(1792), mmfsddas(1793), smfsdsas(1800), smfsddas(1801), mmscsas(1808), mmscdas(1809), smammbdas(1825), mmasmbdas(1833), mmfsdsashwf(1856), mmfsddashwf(1857), smfsdsashwf(1864), smfsddashwf(1865), mmscsashwf(1872), mmscdashwf(1873), smammbdashwf(1889), mmasmbdashwf(1897), dtnm(2048), cam(2049), se100nm(2304), asnqbri(2560) } ACCESS read-only STATUS mandatory DESCRIPTION "Module IDs for the net modules modules" ::= { wfHwModuleEntry 3 } wfHwModuleModRev OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The revision level of the module. High byte is in upper 2 bytes." ::= { wfHwModuleEntry 4 } wfHwModuleModSerialNumber OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The serial number of the module." ::= { wfHwModuleEntry 5 } wfHwModuleArtworkRev OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The Artwork Revision number of the module" ::= { wfHwModuleEntry 6 } wfModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF WfModuleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table is used by the module driver for Barracuda" ::= { wfHwModuleGroup 2 } wfModuleEntry OBJECT-TYPE SYNTAX WfModuleEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Hardware specific information about a slot." INDEX { wfModuleSlot } ::= { wfModuleTable 1 } WfModuleEntry ::= SEQUENCE { wfModuleDelete INTEGER, wfModuleSlot INTEGER, wfModuleTimerFrequency INTEGER, wfModuleBufferBalance INTEGER, wfModuleFddiWeight INTEGER, wfModuleTokenRingWeight INTEGER, wfModuleCsmacdWeight INTEGER, wfModuleSyncWeight INTEGER, wfModuleFreeBufferCredits INTEGER, wfModuleTotalBufferCredits INTEGER, wfModuleRestart INTEGER, wfModuleCsmacd100Weight INTEGER } wfModuleDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "create/delete parameter" DEFVAL { created } ::= { wfModuleEntry 1 } wfModuleSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A unique value for each slot. Its value ranges between 1 and 14. There are products in this family that contain 1, 5, and 14 slots." ::= { wfModuleEntry 2 } wfModuleTimerFrequency OBJECT-TYPE SYNTAX INTEGER { timerdefault(1) } ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the frequency for the buffer balance algorithm to run" DEFVAL { timerdefault } ::= { wfModuleEntry 3 } wfModuleBufferBalance OBJECT-TYPE SYNTAX INTEGER { txrx(1), none(2), rx(3), tx(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable buffer balancing algorithm selectively" DEFVAL { txrx } ::= { wfModuleEntry 4 } wfModuleFddiWeight OBJECT-TYPE SYNTAX INTEGER(1..10) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the weight of the fddi line for the buffer balancing algorithm" DEFVAL { 6 } ::= { wfModuleEntry 5 } wfModuleTokenRingWeight OBJECT-TYPE SYNTAX INTEGER(1..10) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the weight of the token-ring for the buffer balancing algorithm" DEFVAL { 4 } ::= { wfModuleEntry 6 } wfModuleCsmacdWeight OBJECT-TYPE SYNTAX INTEGER(1..10) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the weight of the csmacd line for the buffer balancing algorithm" DEFVAL { 3 } ::= { wfModuleEntry 7 } wfModuleSyncWeight OBJECT-TYPE SYNTAX INTEGER(1..10) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the weight of the sync line for the buffer balancing algorithm" DEFVAL { 2 } ::= { wfModuleEntry 8 } wfModuleFreeBufferCredits OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the number of buffers available to line drivers but not used by them" ::= { wfModuleEntry 9 } wfModuleTotalBufferCredits OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the total number of buffers available to line drivers" ::= { wfModuleEntry 10 } wfModuleRestart OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This attribute should be touched after the queue lengths are configured in the line-records" ::= { wfModuleEntry 11 } wfModuleCsmacd100Weight OBJECT-TYPE SYNTAX INTEGER(1..10) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the weight of the csmacd 100MB line for the buffer balancing algorithm" DEFVAL { 6 } ::= { wfModuleEntry 12 } END -- Wellfleet-MODULE-MIB -- @(#)WSCCS h/mibs-sys.mib 1.1 8/30/95 Wellfleet-SYS-MIB DEFINITIONS ::= BEGIN -- Created by mdl2asn version 3.1 -- Creation date: Wed Aug 30 16:48:50 EDT 1995 IMPORTS IpAddress, Counter, Gauge, TimeTicks, Opaque, enterprises, mgmt FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 DisplayString, mib-2 FROM RFC1213-MIB wfSystem FROM Wellfleet-COMMON-MIB; wfSys OBJECT IDENTIFIER ::= { wfSystem 1 } wfSysDescr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A textual description of the entity including full name and version of the system's hardware type, OS, and networking SW " ::= { wfSys 1 } wfSysObjectID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER ACCESS read-only STATUS mandatory DESCRIPTION "Provides an unambiguous means for determining the MIB type (old product vs. harpoon MIB)." ::= { wfSys 2 } wfSysUpTime OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Time in seconds/100 since the last cold start" ::= { wfSys 3 } wfSysContact OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Contact person for this node and where/how to contact them" ::= { wfSys 4 } wfSysName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Node's fully qualified domain name or administratively assigned name" ::= { wfSys 5 } wfSysLocation OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "Physical Location of this Node" ::= { wfSys 6 } wfSysServices OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "A sum of numbers indicating the set of services the entity offers. For each layer L, add 2**(L - 1). Example: 78 = Layers 2,3,4, and 7." DEFVAL { 78 } ::= { wfSys 7 } wfSysGmtOffset OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The positive or negative offset from Greenwich Mean Time (GMT). This effectively describes the time zone." ::= { wfSys 8 } wfSysMibVersion OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The version of the private management information base currently being used by the system software. Format is: xV.RR" ::= { wfSys 9 } wfSysMibRevision OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The revision level of the private management information base currently being used by the system software." ::= { wfSys 10 } wfSysAgentType OBJECT-TYPE SYNTAX INTEGER { anrptragenttype(29), anhubagenttype(30) } ACCESS read-only STATUS mandatory DESCRIPTION "The network management agent's module type" ::= { wfSys 11 } wfSysMibCounterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Mib II counter Switch" DEFVAL { enabled } ::= { wfSys 12 } END -- Wellfleet-SYS-MIB